EX-48024
4S Serial RS-232 mini PCIe card (Moschip Chipset)
The EX-48024 Mini PCI-Express adapter provides four high performance 16C550-type UART compatible RS-232 serial ports. It is designed for Computer system or Boards to provide instant COM port expansion via the Mini PCI-Express Bus. The card is fully PCI Plug-and-Play compatible and there are no IRQ and I/O address configuration problems.
Interface: Serial RS-232 V.24
FIFO Buffer: 16C550 with 16Byte
I/O addresses and Interrupt: Setting from the System BIOS with IRQ Sharing
Data Bits: 5, 6, 7, 8 / Stop Bits: 1, 1.5, 2 / Parity: none, even, odd, space, mark
Signal: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
Chipset: MosChip MCS9904CV
EX-48270
M.2 NGFF 2 Port SATA3 controller (Asmedia Chipset)
The EX-48270 SATA3 RAID 0/1 M.2 card is an internal controller card for compact PCs, mainboards, notebooks and industrial use. Instead of the mSATA interface, the M.2 bus was developed and used under the Next Generation Form Factor (NGFF) designation. The EX-48270 supports RAID 0 (speed and RAID 1 (data security). The EX-48270 has two internal SATA 3 ports for SATA 2 and 3 SSDs/hard drives. It offers the optimal solution to connect SATA 3 devices via an M.2 slot.
Support SATA 3 / 2 / 1
Serial SATA Revision 3.2 specification
M.2 M key
Native Command Quenue (NCQ)
Supports RAID 0 (stripping/performance) and RAID 1 (mirroring/data security)
Support Serial ATA AHCI Spec. Rev. 1.3
Can also be used without RAID function for single HDD mode
Support hard drives up to 6TB
Chipset: Asmedia ASM1062R
Packaging contents:EX-48270, 2x SATA cable, Driver CD, Manual
EX-48274-2
M.2 NGFF 2 Port USB 3.2 Gen 2x1 card (Asmedia Chipset)
The EX-48274-2 USB 3.2 Gen 2x1 M.2 card provides two SuperSpeed+ USB 3.2 Gen 2x1 ports with two internal 10 pin jacks. It is designed to connect two additional USB 1.1, 2.0, 3.0 and 3.2 end devices to compact PC, mainboards and notebooks. It supports USB 1.1 low-speed (1.5Mbps), full-speed (12Mpbs), USB 2.0 high-speed (480Mbps), USB 3.2 Gen 1 super-speed (5Gbps) and USB 3.2 Gen 2x1 super-speed+ (10Gbps). The EX-48274-2 is the perfect technology to connect external storage, digital cameras, webcam, scanner and more to M.2 bus.
Support USB 3.2 Gen 2x1 (SuperSpeed USB 10Gbps)
Support eXtensible Host Controller Interface (xHCI) Specification 1.1
Interface PCIe 2.0 Gen 2 compliant
M.2 M key
Formfactor: M2 2260
Electric power each port: maximum 15 Watts (5V / 3A)
Hot Swap feature allow you to connect/disconnect devices
Chipset: Asmedia ASM2142
Packaging contents:EX-48274-2, Power cable Molex, Driver CD, Manual
EX-48275-2
M.2 NGFF 2 Port USB 3.2 Gen 2x1 card C-connector (Asmedia Chipset)
The EX-48275-2 USB 3.2 Gen 2x1 M.2 card provides two Super-Speed+ USB 3.2 ports with a 2x 10 pin internal C-female connector. It is designed to connect two more USB 1.1, 2.0, 3.0 and 3.1 devices to compact PCs, mainboards and notebooks. It supports USB 1.1 Low-Speed (1.5Mbps), Full-Speed (12Mpbs), USB 2.0 High-Speed (480Mbps), USB 3.0 Super-Speed (5Gbps) and USB 3.2 Super-Speed+ (10Gbps). It is the perfect technology for connecting external storage housings, digital cameras, webcams, scanners and more to M.2 bus. The EX-48275-2 comes with a power cable with 4 pin Molex connector.
Support USB 3.2 Gen 2x1 (SuperSpeed USB 10Gbps)
Support eXtensible Host Controller Interface (xHCI) Specification 1.1
Interface PCIe 2.0 Gen2 compliant
M.2 M key
Formfactor: M2 2240, 2260 or 2280
Electric power each port: maximum 15Watt (5V / 3A)
Hot Swap feature allow you to connect/disconnect devices
Chipset: Asmedia ASM2142
EX-48200
M.2 NGFF 2S Serial RS-232 card (Exar Chipset)
The EX-48200 RS-232 M.2 card is an internal expansion card for compact PCs, mainboards, notebooks and industrial use. Instead of the mSATA interface, the M.2 bus was developed and used under the Next Generation Form Factor (NGFF) designation. The EX-48200 supports two serial RS-232 high performance UART 16C550 outputs. It is designed to expand two additional serial ports via the M.2 (NGFF) bus. Included with the EX-48200 are two ribbon cables with 9 pin connectors for attachment to the device's chassis.
Interface: RS-232 V.24
M.2 NGFF (Key A) connector
PCI Express 2.0 Gen 1 compliant
±15kV IEC1000-4-2 ESD protection for RS232 I/O's
FIFO Buffer: 16C550 with 256Byte
I/O addresses and Interrupt: Set from the operating system
Data Bits: 5, 6, 7 and 8 / Stop Bits: 1, 1.5, 2
Parity: none, even, odd, space, mark
Flow Control: RTS/CTS, XON/XOFF
Signal RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
Chipset: Exar 17V352
Packaging contents:EX-48200, 2x Slot cable, Driver CD, Manual
EX-48200I
M.2 NGFF 2S Serial RS-232 card with 2.5KV Optical Isolation (Exar Chipset)
The EX-48200I RS-232 M.2 card is an internal expansion card with 2.5KV optical isolation for compact PC, mainboards, notebooks and industrial use. Instead of mSATA interface, M.2 bus was developed and used under the name of Next Generation Form Factor (NGFF). The EX-48200I supports two serial RS-232 high performance UART 16C550 outputs. It is designed to expand two additional serial ports via the M.2 (NGFF) bus. Included with the EX-48200I are two ribbon cables with 9 pin connectors for mounting to the device's chassis.
Interface: RS-232 V.24
M.2 NGFF (Key A) connector
PCI Express 2.0 Gen 1 compliant
2.5KV Optical Isolation
±15kV IEC1000-4-2 ESD protection for RS232 I/O's
FIFO Buffer: 16C550 with 256Byte
I/O addresses and Interrupt: Set from the operating system
Data Bits: 5, 6, 7 and 8 / Stop Bits: 1, 1.5, 2
Parity: none, even, odd, space, mark
Flow Control: RTS/CTS, XON/XOFF
Signal RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
Chipset: Exar 17V352
Packaging contents:EX-48200I, 2x Slot cable, Driver CD, Manual
EX-48220
M.2 NGFF 2S Serial RS-232/422/485 card (Exar Chipset)
The EX-48220 RS-232/422/485 M.2 card is an internal expansion card for compact PCs, mainboards, notebooks and industrial use. Instead of the mSATA interface, the M.2 bus was developed and used under the Next Generation Form Factor (NGFF) designation. The EX-48220 supports two serial RS-232, 422 or 485 high performance UART 16C550 outputs. It is designed to expand two additional serial ports via the M.2 (NGFF) bus. Included with the EX-48220 are two ribbon cables with 9 pin connectors for mounting to the device's chassis.
Interface: RS-232 V.24/ 422 / 485
M.2 NGFF (Key A) connector
PCI Express 2.0 Gen 1 compliant
±15kV IEC1000-4-2 ESD protection for RS232 I/O's
FIFO Buffer: 16C550 with 256Byte
I/O addresses and Interrupt: Set from the operating system
Data Bits: 5, 6, 7 and 8 / Stop Bits: 1, 1.5, 2
Parity: none, even, odd, space, mark
Flow Control: RTS/CTS, XON/XOFF
Signal:
RS-232 - TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422 - 4 Draht: (TXD+/-, RXD+/-) (Fullduplex)
RS-485 - 4 Draht: (TXD+/-, RXD+/-) (Fullduplex)
RS-485 - 2 Draht: (Data-, Data+) (Halfduplex)
Chipset: Exar 17V352
Packaging contents:EX-48220, 2x Slot cable, Driver CD, Manual
EX-48210
M.2 NGFF 2S Serial RS-422/485 card (Exar Chipset)
The EX-48210 RS-422/485 M.2 card is an internal expansion card for compact PCs, mainboards, notebooks and industrial use. Instead of the mSATA interface, the M.2 bus was developed and used under the Next Generation Form Factor (NGFF) designation. The EX-48210 supports two serial RS-422 and 485 high performance UART 16C550 outputs. It is designed to expand two additional serial ports via the M.2 (NGFF) bus. Included with the EX-48210 are two ribbon cables with 9 pin connectors for attachment to the device's chassis.
Interface: RS-422 and 485
M.2 NGFF (Key A) connector
PCI Express 2.0 Gen 1 compliant
±15kV IEC1000-4-2 ESD protection for RS232 I/O's
FIFO Buffer: 16C550 with 256Byte
I/O addresses and Interrupt: Set from the operating system
Data Bits: 5, 6, 7 and 8 / Stop Bits: 1, 1.5, 2
Parity: none, even, odd, space, mark
Flow Control: RTS/CTS, XON/XOFF
Signal:
RS-422: - 4 Draht: (TXD+/-, RXD+/-) (Fullduplex)
RS-485: - 4 Draht: (TXD+/-, RXD+/-) (Fullduplex)
RS-485: - 2 Draht: (Data-, Data+) (Halfduplex)
Chipset: Exar 17V352
Packaging contents:EX-48210, 2x Slot cable, Driver CD, Manual
EX-48210I
M.2 NGFF 2S Serial RS-422/485 card with 2.5KV Optical Isolation (Exar Chipset)
The EX-48210I RS-422/485 M.2 card is an internal expansion card with 2.5KV optical isolation for compact PCs, mainboards, notebooks and industrial use. Instead of the mSATA interface, the M.2 bus was developed and used under the Next Generation Form Factor (NGFF) designation. The EX-48210I supports two serial RS-422 and 485 high performance UART 16C550 outputs. It is designed to expand two additional serial ports via the M.2 (NGFF) bus. Included with the EX-48210I are two ribbon cables with 9 pin connectors for attachment to the device's chassis.
Interface: RS-422 and 485
M.2 NGFF (Key A) connector
PCI Express 2.0 Gen 1 compliant
2.5KV Optical Isolation
±15kV IEC1000-4-2 ESD protection for RS232 I/O's
FIFO Buffer: 16C550 with 256Byte
I/O addresses and Interrupt: Set from the operating system
Data Bits: 5, 6, 7 and 8 / Stop Bits: 1, 1.5, 2
Parity: none, even, odd, space, mark
Flow Control: RTS/CTS, XON/XOFF
Signal:
RS-422 - 4 Draht: (TXD+/-, RXD+/-) (Fullduplex)
RS-485 - 4 Draht: (TXD+/-, RXD+/-) (Fullduplex)
RS-485 - 2 Draht: (Data-, Data+) (Halfduplex)
Chipset: Exar 17V352
Packaging contents:EX-48210I, 2x Slot cable, Driver CD, Manual
EX-48240
M.2 NGFF 4S Serial RS-232/422/485 card (Exar Chipset)
The EX-48240 RS-232/422/485 M.2 card is an internal expansion card for compact PCs, mainboards, notebooks and industrial use. Instead of the mSATA interface, the M.2 bus was developed and used under the Next Generation Form Factor (NGFF) designation. The EX-48240 supports four serial RS-232, 422 or 485 high performance UART 16C550 outputs. It is designed to expand four additional serial ports via the M.2 (NGFF) bus. Included with the EX-48240 are four ribbon cables with 9 pin connectors for attachment to the unit's chassis.
Interface: RS-232 V.24/ 422 / 485
M.2 NGFF (Key A) connector
PCI Express 2.0 Gen 1 compliant
±15kV IEC1000-4-2 ESD protection for RS232 I/O's
FIFO Buffer: 16C550 with 256Byte
I/O addresses and Interrupt: Set from the operating system
Data Bits: 5, 6, 7 and 8 / Stop Bits: 1, 1.5, 2
Parity: none, even, odd, space, mark
Flow Control: RTS/CTS, XON/XOFF
Signal:
RS-232 - TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422 - 4 Draht: (TXD+/-, RXD+/-) (Fullduplex)
RS-485 - 4 Draht: (TXD+/-, RXD+/-) (Fullduplex)
RS-485 - 2 Draht: (Data-, Data+) (Halfduplex)
Chipset: Exar 17V352
Packaging contents:EX-48240, 4x Slot cable, Driver CD, Manual
EX-3605
M.2 NGFF to SATA converter with 2.a5-inch metal frame
The EX-3605 converter can used for a replacement of a 2.5-inch hard drive or SSD. For connect the EX-3605 need a SATA connector from the mainboard or from a SATA controller. You can use following M.2 NGFF module: 2280, 2260, 2242 and 2230. The module with B-key and also B+M-key will be supported.
Convert M.2 NGFF SATA SSD to standard 2.5” SATA Form Factor
M.2 NGFF type 2280-xx-B connector on board
Supports M.2 NGFF type 2280, 2260, 2242 and 2230 plated-hole
100% compatible with 2.5-inch SATA drive mechanical specification
22 pin SATA connector (signal and power)
M.2 NGFF SATA SSD can be the primary bootable device containing the OS
Transparent to the operating system and don’t need driver
With the product we delivery 4 screw for fix the 2.5” frame in the computer case and also one screw for fix the M.2 NGFF module
Packaging contents:EX-3605, 4x screw for fix the 2.5” frame, 1x screw for fix the M.2 modules, Manual
EX-48023
mini PCIe 2S Serial RS-232/1P Parallel, Multi I/O card
The EX-41150 PCI Multi I/O adapter provides s high performance 16C550-type UART compatible RS-232 serial ports and one Parallel Centronics EPP/ECP port. It is designed for PC, thin client or server to provide instant COM and LPT port expansion via the PCI Bus. The card is fully PCI Plug-and-Play compatible and there are no IRQ and I/O address configuration problems. It additionally provides +5V and +12V via the pin 9 at the male connector for a POS System (Power over System).
Interface: Serial RS-232 V.24 / Parallel EPP/ECP
FIFO Buffer: 16C550 with 16Byte
I/O addresses and Interrupt: Setting from the System BIOS with IRQ Sharing
Data Bits: 5, 6, 7, 8 / Stop Bits: 1, 1.5, 2 / Parity: none, even, odd, space, mark
Signal: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
Support Mother-Board with 5V and 3.3V
Windows WHQL certified
Chipset: MosChip MCS9835CV
EX-48080-2
mini PCIe SATA 3 controller for two HDD and SSD drives
The EX-48080-2 is a powerful SATA 3 controller based on the new mini PCI-Express technolo-gy. It does not support RAID function. The EX-48080-2 has two SATA 3 connectors for SATA 2 / 3 and SSD hard disks. It offers the right solution to connect SATA 3 devices via a mini PCI-Express slot.
Support 1-lane 5Gbps PCI-Express Gen2 Bus
Don’t supports RAID function
Compatible to SATA / SATA 2/3 and SSD drives
Co-resides with mainboard SATA devices
MSU Supports HyperDuo Modes: Safe and Capacity
Compliant with Serial ATA AHCI (Advanced Host Controller Interface) Specification Rev 1.0
Supports Gen1m and Gen2m SATA PHY
Support hard drives up to 6TB
Chipset: ASM1061
Packaging contents:EX-48080-2, 1x SATA cable, 1x Holder Driver CD, Manual
EX-48010-3
Mini PCIe USB 3.2 Gen 1 with 2 ports (NEC chipset)
The EX-48010-3 USB 3.2 Gen 1 Mini PCIe card adds two super-speed USB 3.2 Gen 1 ports to your system. Alternatively, the internal 19-pin header can be used for internal connections. It supports USB 1.1 Low-Speed (1.5Mbps), Full-Speed (12Mpbs), USB 2.0 High-Speed (480Mbps) and USB 3.2 Gen1 Super-Speed (5Gbps) and is suitable for any USB connection such as external storage enclosures, webcams, printers, scanners and more. The card is powered by the computer via the floppy connector and provides 900mA per port.
USB 3.2 Gen 1 Mini PCIe card with two ports
Compatible with Microsoft Windows Standard Open HCD driver and Intel's eXtensible Host Controller Interface (xHCI)
Supports up to 123 devices
Fully compliant with PCI Express 2.0 specifications
Backward compatible with USB 1.1 and 2.0
Supports hot swapping and plug & play
With adapter cable 19-pin to 2x USB-A ports on standard profile bracket
Packaging contents:EX-48010-3, power cable, 19-pin adapter cable with standard profile bracket to 2x USB-A, driver CD, manual
EX-48010-2
mini PCIe USB 3.2 Gen 1 with 2 ports (Renesas Chipset)
The EX-48010-2 mini PCIe USB 3.2 Gen 1 (previously called USB 3.0) card provides two super-speed USB 3.0 ports. It is designed to connect two additional USB 1.1, 2.0 or 3.2 Gen 1 end devices to Computersystems or motherboards via the mini PCI-Express bus. It supports USB 1.1 low-speed (1.5Mbps), full-speed (12Mpbs), USB 2.0 high-speed (480Mbps) and USB 3.2 Gen 1 super-speed (5Gbps). The EX-48010-2 is fully PCIe plug-and-play compatible, so it has no conflicts with IRQ and I/O addresses. It is the perfect technology for external storage, digital cameras, webcam, scanners and more. To support power to the external USB 3.2 Gen 1 ports, you don't need an additional power connection from the PC power supply.
Compliant with USB 3.2 Gen 1 and Intel xHCI specification
Supports all USB Compliant Data Transfer Type such as Control/Bulk/Interrupt/Isochronous
Support up to 123 device
Fully PCI Express Gen2 sSpecification compliant
Support “Hot Swapping” and “Plug-and-Play”
Chipset: Renesas D720202
Packaging contents:EX-48010-2, Standard bracket, power cable, 20 pin adapter cable for two USB 3.2 Gen 1 ports, Driver CD, Manual
EX-3649
PCIe (x2) RAID card for each two M.2 NGFF and two mSATA module
With the EX-3649 controller you can expand the computer with two mSATA (Half Size and Full Size) as well as two M.2 NGFF 2280, 2260, 2242 or 2230 modules with B-Key as well as B+M Key. The controller supports RAID 0/1 and JBOD. The EX-3649 requires at least one PCI-Express x2 slot.
PCIe (x2) board for each two M.2 NGFF and mSATA SSD drives
Build in ASM1062R high performance processor
Support RAID 0 / 1 and JBOD and Port Multiplier for two different drives
Supports M.2 NGFF type 22110, 2280, 2260 and 2242 plated-hole mSATA Half Size and Full Size
Supports PCIe specification Rev. 2.0
4A maximum output current
Short circuit protection as Thermal shutdown protection
Packaging contents:EX-3649, Screws for fix M.2 or mSATA moules, Assembly Guide
EX-3655
PCIe (x4) controller for two M.2 NGFF Module incl. Low Profile bracket
With the EX-3655 controller you can expand the computer with two M.2 NGFF slot. The modules M.2 NGFF 22110, 2280, 2260 and 2242 can be used. Modules with B-Key as well as B+M Key are supported. The EX-3655 requires a PCI-Express x4 slot. With the EX-3655 a low profile bracket for narrow computer cases up to 8 cm height is included.
PCIe (x4) board for two M.2 NGFF SSD drives
Supports M.2 NGFF type 22110, 2280, 2260 and 2242 plated-hole
Power from the PCIe bus or from the 4 pin power connector
Can be fitted on both sides
Supports PCIe 1.0, 2.0 and 3.0 mainboard
Pin header on board for drive LED connection
Packaging contents:EX-3655, 1x screw for fix M.2 modules, Low Profile bracket, Manual
EX-3660
PCIe (x4) controller for two SATA M.2 NGFF and one PCIe M.2 NGFF module
With the EX-3660 controller you can equip the computer with two SATA M.2 NGFF modules as well as one PCIe M.2 NGFF module. The modules M.2 NGFF 22110, 2280, 2260 and 2242 can be used. Modules with B-Key as well as B+M Key are supported. The EX-3660 requires a PCI-Express x4 slot. A low profile bracket for narrow computer cases up to 8 cm height is included with the EX-3660.
Attention:For the two SATA M.2 NGFF module you must use two SATA cable what is connect to the mainboard.
PCIe (x4) board for two SATA M.2 NGFF and one PCI M.2 NGFF SSD
Supports M.2 NGFF type 22110, 2280, 2260 and 2242 plated-hole
Power from the PCIe bus or from the 4 pin power connector
Supports dual-sided SSD module 1.5mm component height on the top and bottom side
Supports PCIe 1.0, 2.0 and 3.0 mainboard
Supports Native Command Queuing (NCQ)
Packaging contents:EX-3660, 3x screw for fix M.2 modules, Low Profile bracket, Manual
EX-3650
PCIe (x4) controller to M.2 NGFF module incl. Low Profile bracket
With the EX-3650 controller you can add in your Computersystem a M.2 NGFF slot. You can use following M.2 NGFF module: 2280, 2260 and 2242. The EX-3650 need a PCI-Express x4 slot.
Convert M.2 NGFF PCIe SSD to work in main board PCIe x4 bus slot
Supports M.2 NGFF type 2280, 2260 and 2242 plated-hole with M-Key or B+M-Key based on PCIe
Supports NVM Express (NVMe)
Can be installed as boot drive
Transparent to the operating system and don’t need driver
Maximum high of 1.5mm component height on the top and bottom side
Supports dual-sided SSD module
Supports PCIe 1.0, 2.0 and 3.0 mainboard
Pin header on board for drive LED connection
Packaging contents:EX-3650, 1x screw for fix M.2 modules, Low Profile bracket, Manual
EX-48100
PCIe to mini PCIe converter card
The EX-48100 PCI-Express to mini PCIe adapter card provides a 52-pin mini PCIe female connector for a desktop PC with PCI-Express slots. It is an ideal solution to share all mini PCIe cards with your desktop PC. The EX-48100 don’t need drivers.The card is fully PCI Plug-and-Play compatible and there are no IRQ and I/O address configuration problems.
Full x1 PCI Express Throughput, 250 or 500MBytes/sed.
Fully Compliant with PCI Express Base Specifications Rev. 1.0a to 2.1
Supports Standard and Low Profile From Factors
Provides 1 x 52-pin mini PCI Express female connector
Supports 1 USB Port for USB-based Cards
Provides 2 mounting screws to fasten the mini PCIe Cards
No Driver Required of support in all OS platforms (it might need drivers for the mini PCIe card itself, but no need for this adapter card)
Supports standard 2.00 x 1.18 inch mini PCIe cards
EX-3608
SATA 3 to 2x M.2 & mSATA (RAID) with 3.5-inch metal frame or PCIe slot
The EX-3608 converter can used for a replacement of a 3.5-inch hard drive or SSD. For connect the EX-3608 need a SATA 3 connector from the mainboard or from a SATA 3 controller. You can use two M.2 NGFF module 2280, 2260, 2242 and 2230 with B-key as two mSATA module with Half Size or Full Size. The EX-3608 support RAID 0/1 and JBOD. Included it’s a bracket for install vertical in the PC.
Built-in ASM1092R high performance processor
Supports M.2 NGFF type 2280, 2260, 2242 and 2230 plated-hole
Can connect simultaneously two other SATA 2 devices
100% compatible with 2.5-inch SATA drive mechanical specification
Support RAID mode: RAID 0 (fast) / RAID 1 (safe) and JBOD (volume)
RAID mode switch by hardware strapping or GUI controller
22 pin SATA connector (signal and power)
Support SATA 3 Revision 3.2
Transparent to the operating system and don’t need driver
Additional it’s include a bracket for install on the backside from the PC
Packaging contents:EX-3608, 4x screw for fix the 2.5” frame, Assembly Guide
EX-3607
SATA 3 to 2x M.2 SSD & SATA 2 (RAID) with 2.5-inch metal frame (9.5mm)
The EX-3607 converter can used for a replacement of a 2.5-inch hard drive or SSD. For connect the EX-3606 need a SATA 3 connector from the mainboard or from a SATA 3 controller. You can use following M.2 NGFF module: 2280, 2260, 2242 and 2230 and support the module with B-key. Additional can connect SATA 2 devices. The EX-3607 support RAID 0/1 and JBOD. Included it’s a bracket for install vertical in the PC.
Built-in ASM1092R high performance processor
Supports M.2 NGFF type 2280, 2260, 2242 and 2230 plated-hole
Can connect simultaneously two other SATA 2 devices
100% compatible with 2.5-inch SATA drive mechanical specification
Support RAID mode: RAID 0 (fast) / RAID 1 (safe) and JBOD (volume)
RAID mode switch by hardware strapping or GUI controller
22 pin SATA connector (signal and power)
Support SATA 3 Revision 3.2
Transparent to the operating system and don’t need driver
Additional it’s include a bracket for install on the backside from the PC
Packaging contents:EX-3607, 4x screw for fix the 2.5” frame, Assembly Guide
EX-3606
SATA 3 to 2x M.2 SSD Enclosure RAID, 2.5inch (9.5mm)
The EX-3606 converter can used for a replacement of a 2.5-inch hard drive or SSD. For connect the EX-3606 need a SATA 3 connector from the mainboard or from a SATA 3 controller. You can use following M.2 NGFF module: 2280, 2260, 2242 and 2230 and support the module with B-key and also B+M-key. The EX-3606 support RAID 0 / 1 and JBOD.
Built-in ASM1092R high performance processor
Supports M.2 NGFF type 2280, 2260, 2242 and 2230 plated-hole
100% compatible with 2.5-inch SATA drive mechanical specification
Support RAID mode: RAID 0 (fast) / RAID 1 (safe) and JBOD (volume)
RAID mode switch by hardware strapping or GUI controller
22 pin SATA connector (signal and power)
Support SATA 3 Revision 3.2
Transparent to the operating system and don’t need driver
Green LED indicate SATA 3 host active, red LED indicate M.2 NGFF SSD error
Packaging contents:EX-3606, 4x screw for fix the 2.5” frame, Assembly Guide
EX-3683
SATA3 to 2x mSATA SSD (RAID) with 2.5-inch metal frame (9.5mm)
The EX-3683 converter can used for a replacement of a 2.5-inch hard drive or SSD. For connect the EX-3683 need a SATA 3connector from the mainboard or from a SATA 3 controller. You can use the mSATA module: Half Size and Full Size. The EX-3683 support RAID 0 / 1 and JBOD.
Built-in ASM1092R high performance processor
Supports Half Size or Full Size module
100% compatible with 2.5-inch SATA drive mechanical specification
Support RAID mode: RAID 0 (fast) / RAID 1 (safe) and JBOD (volume)
RAID mode switch by hardware strapping or GUI controller
22 pin SATA connector (signal and power)
Support SATA 3 Revision 3.2
Transparent to the operating system and don’t need driver
Green LED indicate SATA 3 host active, red LED indicate M.2 NGFF SSD error
Packaging contents:EX-3683, 4x screws for mounting the 2.5" frame, manual